VJT0P - 13 FT IEC C14 to C13 Rack PDU Power Cord

The VJT0P is a grounded IEC power jumper designed to connect an IEC C13 receptacle on a rack PDU, UPS, or power-distribution device to the IEC C14 power inlet on compatible servers, storage systems, network switches, workstations, monitors, and other IT equipment.

This is a straight, black, approximately 13-foot / 4-meter PDU-style power cord. It is not a standard wall-outlet power cable and does not include a NEMA wall plug.

Technical Specifications

• Part Number: VJT0P
• Cable Type: Rack PDU / UPS power jumper and extension cable
• Source Connector: IEC 60320 C14 male
• Equipment Connector: IEC 60320 C13 female
• Length: Approximately 13 FT / 4 meters
• Maximum Current: Up to 13A depending on cord revision and printed rating
• Voltage Rating: Application and cord-label dependent; use only within the voltage printed on the physical cable
• Typical Wire Construction: Three-conductor 16 AWG grounded cable
• Typical Jacket Type: SJT flexible thermoplastic / PVC
• Connector Orientation: Straight molded connectors
• Color: Black
• Grounding: Three-conductor grounded
• Typical Jacket Markings: 60°C, 300V insulation, VW-1 / FT2; jacket ratings are not a substitute for the completed cordset rating
• Connection Direction: C14 male end connects to the PDU or UPS; C13 female end connects to the equipment’s C14 inlet
• Quantity: One power cord

Interchangeable / Replacement Part Numbers

Direct Service Part Numbers: VJT0P, 0VJT0P
Current Same-Length Functional Equivalent: 01F3W
Ordering Cross-Reference: 450-ACFY

⭐ Related Parts and Cross-Sell

➕ 95HR5 - 1600W 80 Plus Platinum Hot-Plug Power Supply
➕ 573696-001 - 6 FT IEC C14 to C13 PDU Jumper Power Cord — shorter 6-foot alternative
➕ 5120P - 6 FT 125V NEMA 5-15P to IEC C13 Wall Power Cord — alternative for a standard North American wall outlet

✅ Confirmed Compatibility

Compatibility is determined by the installed power-supply inlet and the source receptacle. The equipment must have an IEC C14 inlet, while the PDU or UPS must provide an IEC C13 receptacle. The connected load must remain within the lowest current and voltage rating printed on the cord, equipment, PDU, and UPS.

✔️ PowerEdge Legacy Rack Servers: 1950, 2970
✔️ PowerEdge C-Series: C2100, C4130, C5125, C6100, C6145, C6400 configurations equipped with an IEC C14-input power supply
✔️ PowerEdge R200-Series: R200, R210, R210 II, R230, R240, R250, R260
✔️ PowerEdge R300-Series: R330, R340, R350, R360
✔️ PowerEdge R400-Series: R410, R415, R420, R430, R440
✔️ PowerEdge R500-Series: R510, R515, R530, R540
✔️ PowerEdge R600-Series: R610, R620, R630, R640, R6415, R650, R6515, R660, R6615, R6625
✔️ PowerEdge R700-Series: R715, R720, R730, R730xd, R740, R740xd, R740xd2, R7415, R7425, R7515, R760, R7615, R7625, R7725
✔️ PowerEdge R800-Series: R805, R810, R815, R820, R830, R840
✔️ PowerEdge R900-Series: R900, R905, R910, R930, R940, R940xa
✔️ PowerEdge Tower Servers: T110, T130, T140, T300, T310, T320, T330, T340, T420, T430, T440, T550, T605, T610, T630, T640, T710
✔️ PowerEdge Rugged and Edge Systems: XR2, XR4000R, XR4000Z, XR7620, XR8000r configurations with IEC C14 inlets
✔️ PowerEdge VRTX: Configurations using 1100W or 1600W IEC C14-input power supplies
✔️ PowerEdge FX2 / FX2s: Configurations using the 1600W IEC C14-input power-supply family
✔️ PowerEdge C6400: Configurations using the 1600W IEC C14-input power supply; not compatible with C20-input 2000W, 2400W, or 2600W supplies
✔️ Precision Rack Workstations: Precision 7920 Rack and Precision 7920 XL Rack configurations equipped with IEC C14-input power supplies
✔️ Networking X-Series: X1018, X1026, X1052
✔️ PowerSwitch N1500-Series: N1500 Series
✔️ PowerSwitch N2000-Series: N2000 Series, N2024, N2024P, N2048, N2048P, N2200-ON
✔️ PowerSwitch N3000-Series: N3000 Series, N3024, N3024EF-ON, N3024EP-ON, N3024ET-ON, N3024F, N3024P, N3048, N3048EP-ON, N3048ET-ON, N3048P
✔️ PowerSwitch S3000 / S4000-Series: S3248T-ON, S4048-ON, S4048T-ON, S4128, S4148, S4148U-ON, S4248FB-ON, S4300-ON
✔️ PowerSwitch S5000 / S6000-Series: S5212F-ON, S5224F-ON, S5232F-ON, S5248F-ON, S5296F-ON, S6100-ON
✔️ PowerSwitch Z-Series: Z9100-ON, Z9264F-ON, Z9332F-ON
✔️ Legacy PowerVault Systems: DL2000, DL2200, DL2300, DR4100, DX6104 CSN, DX6104 SCN, DX6104 SN, DX6112 SN, MD1120, MD3000i, NX200, NX3100
✔️ PowerVault MD-Series: MD2412, MD2424, MD2460
✔️ PowerVault ME400-Series: ME412, ME424
✔️ PowerVault ME500-Series: ME5012, ME5024, ME512, ME5212, ME5224, ME524
✔️ PowerVault NX-Series: NX3340, NX440
✔️ BSN Systems: BSN Controller Node, BSN Recorder Node, BSN Services Node
✔️ MSA Storage Systems: MSA 1060, MSA 2060, MSA 2062 configurations using IEC C14-input power supplies
✔️ ProLiant and Apollo Systems: Configurations using compatible 800W, 1000W, or 1500W IEC C14-input power supplies within the cord’s printed rating
✔️ Nexus and UCS Platforms: Nexus 2000, Nexus 9000, UCS C-Series, and related platforms that support a C13-to-C14 PDU jumper
✔️ General Rack Equipment: Servers, storage arrays, network switches, routers, firewalls, workstation systems, monitors, computers, and other equipment equipped with a standard IEC C14 inlet
✔️ PDU and UPS Sources: Rack PDUs and UPS systems providing an IEC C13 output receptacle at the voltage and current required by the connected equipment

☑️ Key Features

☑️ Straight IEC C14 male to IEC C13 female configuration
☑️ Approximately 13-foot / 4-meter cable for flexible rack routing
☑️ Grounded three-conductor construction
☑️ Designed for PDU, UPS, server, storage, networking, and workstation applications
☑️ Compatible with standardized IEC C13 and C14 connections
☑️ Molded connectors provide strain relief and secure connections
☑️ Useful for rack installations where additional cable length is required

⚙️ Fit Notes

• VJT0P identifies the 13-foot / 4-meter cable. Do not fulfill a 6-foot cable under this part number without checking the physical label and measuring the cord.
• The exact current, voltage, temperature, certification, and jacket markings printed on the physical cord always take precedence.
• This cable does not have a NEMA wall plug. It is intended for an IEC C13 outlet on a PDU, UPS, or compatible power-distribution device.
• The cable does not convert voltage. The source voltage must be supported by the connected equipment.
• One cable is required for each power supply in a redundant or dual-PSU system.
• Do not use with IEC C16, C20, C22, C19, right-angle, or locking-only connections unless specifically verified.
• Systems using high-current IEC C20 inlets require an IEC C19-to-C20 cable instead.
• A physical connector match does not override the cord’s printed electrical rating.
• Inspect the cable, insulation, molded connectors, and grounding contacts before installation.